We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
Seal-Once - NANO Penetrating Wood Sealer (1 Gallon)
SKU
SO7214-1
In stock
NANO Penetrating Wood Sealer is a waterproof stain & finish that deeply penetrates the wood surface. It will protect and stabilize against water damage and decay. The water based formula uses our proprietary nanotechnology. It forms a flexible breathable barrier by coating the wood fibers at the cellular level.
- Helps resist wood rot, wood decay, mold, mildew and fungi growth
- Non-film forming clear formula allows wood to silver naturally and evenly
- Eliminates wood warping & cupping caused by water intrusion
FREE SHIPPING on 5 gallon pails!
5 Gallon - Purchase Here
Category: Seal-Once
Related Products
RECOMMENDED USES:
- Fences
- Wood Siding
- Log Homes
- Shake Roofs
- Thermally Modified Wood
- Outdoor Furniture
- Swing Sets
- Pergola
- Shakes
- Decks
FEATURES & BENEFITS:
- Water-based, Ultra-Low VOC
- Eco-friendly, Non-toxic, No Odor
- Won't harm people, pets or plants
- Penetrates below the surface
- Creates flexible, breathable barrier
- Helps resist mold, mildew & wood rot
- Stabilizes wood from warping
- UV barrier protects from sun rays
- Extends natural life of wood
- Easy soap & water clean-up
- Clear allows the wood to grey naturally
SEAL-ONCE® has been leading the innovation in the use of nanotechnology to create long-lasting, Eco-friendly wood sealers & tinted wood stains since 2005. Our New & Improved NANO Penetrating Wood Sealer, deeply penetrates the surface of wood to protect and stabilize against water damage and decay. Unlike many top-coat sealers that trap moisture below the surface, NANO creates a long-lasting, flexible, breathable barrier, that allows water vapor to escape & help prevent damage. NANO is warranted to prevent water intrusion for up to 10 years on vertical & up to 6 years on horizontal surfaces.
SEAL-ONCE® NANO Waterproofing Wood Sealer & Stain is ideal for use on unfinished interior and exterior wood surfaces. The clear, non-film forming formula allows the wood to age naturally without decay, morphing to a rich silver-gray over time. It can also be used as a wood stain, when mixed with a full range of semi-transparent tints to enhance the appearance & provide additional UV protection from sun rays.
Material Safety Data Sheet
Product Data Sheet
Preparation:
- Wet the surface.
- Clean the surface with a solution of 1 cup SEAL-ONCE All Wood Cleaner to 1 gallon of water. Apply this solution to the wood with a garden pump sprayer.
- Let the solution sit for 15-20 minutes. Do not let the cleaner dry. Keep it wet.
- Power wash the cleaning solution from the wood. To Prevent damaging the wood do not exceed 500psi. Keep the nozzle 1-2 feet away from the surface.
- Rinse thoroughly.
- Let the surface dry 1-2 days before application of Seal-Once.
How to apply:
- Do not use if air or surface temperature is below 45°F/7.22°C or above 95°F/35°C.
- Do not apply in rain or when rain is expected within 12-24 hours. For all stains (including Ready-Mixed), intermix gallons and stir to ensure color consistency.
- DO NOT THIN. Mix well. Stir contents or shake thoroughly prior to use.
- Test a small area to ensure acceptable appearance and penetration.
- Apply first coat with a synthetic brush; pump-up garden sprayer; air-assisted and/or airless sprayer. Use 15-17 tip and medium to coarse spray pattern. When spraying, always back brush for best results.
- Second coat can be applied once first coat has penetrated but is still damp. Second coat must be applied within one hour of applying first coat.
- For best results, apply in the shade and out of direct sunlight.
- When applying in direct sunlight and wood surface is hot, spray with a mist of water and apply SEAL-ONCE NANO immediately on dampened surface.
- Apply to all surfaces. Apply SEAL ENDS ONCE® to wood ends.
- Do not use with other waterproofing products.
- Remove excess stain sitting or puddling on the surface. Back brush or use a rag to wipe away any runs, drips, or puddles that have not soaked in.
Dry Time/Clean Up:
- Allow approximately 2-3 hours for surface to dry, depending on temperature and humidity.
- Allow 12-24 hours for full cure, depending on temperature and humidity.
- When recoating, apply as soon as previous coat has penetrated and surface is damp, not wet. Second coat must be applied within one hour of applying the first coat.
- Clean all application with warm soapy water.
- Disposal: soap and water cleanup; no special disposal procedure needed.
- Store unused product above 32°F/0°C to protect from freezing.
- Shelf life (unopened): 3 years
| Shipping Details | Shipping is provided by Fed-Ex Ground for single gallon purchases and many times ships the same business day if ordered before noon EST. Most always 1-3 business days shipping standard.
|
|---|---|
| Color | Clear Matte |
| Manufacturer | U-C Coatings |
